For the use method of standard Ultrasonic cleaning, the specific steps are as follows:

1. 準備工作：確保清洗機的供電插座可用，并檢查設備的電源線是否完好無損。同時，檢查清洗機內部是否有殘留物，如有需要清除。

1. Preparation: Ensure that the power socket of the cleaning machine is available and check if the power cord of the equipment is intact. At the same time, check if there is any residue inside the cleaning machine, and if necessary, remove it.

2. 配置清洗劑：根據清洗對象的不同，選擇適合的清洗劑，并按照清洗劑的要求配置合適的濃度。將清洗劑加入清洗機的清洗槽中，注意不要超過大標識線。

2. Configuration of cleaning agents: Select suitable cleaning agents based on the different cleaning objects, and configure the appropriate concentration according to the requirements of the cleaning agent. Add the cleaning agent to the cleaning tank of the cleaning machine, taking care not to exceed the maximum marking line.

3. 裝載清洗物：將待清洗的物品放入清洗機的清洗槽中。注意避免過度密集或擁擠，以免影響清洗效果。

3. Loading cleaning materials: Place the items to be cleaned into the cleaning tank of the cleaning machine. Pay attention to avoiding excessive density or crowding to avoid affecting the cleaning effect.

4. 設置參數：根據清洗對象的質地、尺寸和臟污程度，設置合適的清洗參數。清洗參數包括清洗時間、溫度、液位、噴淋壓力等。應根據清洗機的說明書進行設置。

4. Setting parameters: Set appropriate cleaning parameters based on the texture, size, and degree of dirt of the cleaning object. The cleaning parameters include cleaning time, temperature, liquid level, spray pressure, etc. It should be set according to the instructions of the cleaning machine.

5. 開始清洗：按下清洗機上的啟動按鈕，開始清洗過程。在清洗過程中，清洗機會根據預設的參數進行自動操作，包括噴淋、浸泡、清洗液循環等。

5. Start cleaning: Press the start button on the cleaning machine to start the cleaning process. During the cleaning process, the cleaning machine automatically operates according to preset parameters, including spraying, soaking, cleaning solution circulation, etc.

6. 監測清洗過程：在清洗過程中，可以通過觀察清洗機的顯示屏或指示燈來監測清洗機的工作狀態。確保整個清洗過程順利進行，并根據需要進行必要的調整。

6. Monitoring the cleaning process: During the cleaning process, the working status of the cleaning machine can be monitored by observing its display screen or indicator light. Ensure the smooth progress of the entire cleaning process and make necessary adjustments as needed.

7. 完成清洗：清洗完成后，清洗機會自動停止工作。此時，打開清洗機的排水閥，將廢液排出。然后取出清洗物，可用干凈的布或紙巾擦干，使其完全干燥。

7. Complete cleaning: After the cleaning is completed, the cleaning machine will automatically stop working. At this point, open the drain valve of the cleaning machine to discharge the waste liquid. Then remove the cleaning material and wipe it dry with a clean cloth or tissue until it is completely dry.

8. 清洗機的維護：清洗結束后，要對清洗機進行適當?shù)木S護和清潔。清洗機應經常清洗內部管道和過濾器，并定期更換或補充清洗液。

8. Maintenance of the cleaning machine: After cleaning, appropriate maintenance and cleaning should be carried out on the cleaning machine. The cleaning machine should regularly clean the internal pipelines and filters, and regularly replace or supplement the cleaning solution.

以上是標準超聲波清洗機的使用方法的一般步驟，具體使用方法可能因不同型號的清洗機而略有差異。使用前請務必仔細閱讀清洗機的操作說明書，并根據實際情況進行操作。

The above is a general procedure for the use of the standard Ultrasonic cleaning. The specific use method may vary slightly with different models of the cleaner. Before use, please carefully read the operating manual of the cleaning machine and operate according to the actual situation.